The popularity of these battery-powered toy cars is increasing day by day. There are many models of Pub Wheels available in the market, not all Power Wheels cars come with remote control. If you have bought a Power Wheels car for your child and you want to control it remotely by yourself. However, you can change the toy car and control it remotely with some technical skills.
Do you want to know How to Make Power Wheels Remote Control? Well, then you’ve come to the right place. In this article, we will discuss how to convert a power wheels car to a remote control. To do this you need to know how to make a power wheel remote control and how to change different things on your toy card.
How to Make Power Wheels Remote Control
All you have to do is start collecting the necessary materials. However, the items needed for remotely controlled power wheels can be a bit expensive. However, before you start work, you need to collect all the necessary materials below and keep them close at hand. If you want to get additional information regarding the topic, you can simply go with How Long Does A 12v Power Wheels Battery Charge Last.
- Light Switches
- Two Battery holders
- Power Wheels toy car
- Screws
- FlySky transmitter and receiver
- Large Servo
Step 1: Prepare the Vehicle
You need to get the Power Wheels car ready before you start work. You may find dirt under the hood before the conversion work, which would be nice to clean. But it would be best if you know how to do it. Then you can decide exactly where to install the parts. Now remove the necessary parts from the car and make it very easy to access where it will work.
Step 2: Remove Control Parts
When you install the new system on the car, take a picture of the wires of the remote control parts of the faulty system for reference. You can easily do this by looking at this picture later when installing a new system.
Now to install the new system on the car, remove all parts of the faulty remote control system. Flip the car so you can easily access the paddle tab. Press the four tabs to remove the gas pedal from the power wheels car, as well as clear any attachment wires around the pedal area. Those who wish to go into more detail about the power wheel battery charging period can learn about How To Make Power Wheels Dune Buggy Go Faster.
If there is any excess plastic around the paddle area, cut it off. Because it would be best if there was nothing in the paddle area. When you do all these things, make sure that no one hangs up. Do not keep it near the child while working, accidents can happen.
Step 3: Install the New Servo on Toy Car
In this step, you need to remove some parts to attach the servo. First, you need to remove the toy battery from the toy car as well as disconnect the wires from the battery connector to the toy car. Now you attach two plus-shaped pieces to the bottom of the toy car dashboard that comes with the servo.
Attach the steering servo using a drill and screw. Then attach them to the body of the hard drive by drilling holes and screwing the ends of the steering wheel. You need to make sure that all connections are properly aligned with the server. Use two pieces of wire to secure them to the servo.
Step 4: Connect the receiver with Servo
The receivers of the Power Wheels car remote are initially small. So you can use electrical tape to attach the receiver to the dashboard. Most servos have ports for two channels. You need to read your user manual to find out which channel you want to connect the receiver to.
If you have found the channel, connect the connector to the receiver in the appropriate channel. Now connect the remote to the receiver and check if it is OK. You can add a light switch to the second channel of the receiver so that the receiver turns it off whenever you want.
In addition, when you notice that the remote is not working, check to see if there is a loose connector or if you are doing something wrong. Check that the power circuit is complete, if the circuit is incomplete then the remote will not work. If you are interested to know more tips, you can go with How To Charge A Power Wheels.
Step 5: Test Drive
If all goes well then your work is done. Now you can see with a test drive if everything is OK. To test how well your new remote control works, you can take the car for a test drive around the compound. Moreover, after reinstalling the parts removed from the car, you must make an experimental drive.
You must give a test drive for the safety of your child. When you give a test drive, the power wheels will be able to catch if there is any defect in the car. Which can save your child from many kinds of accidents. Also, do a test drive with a baby to find out how the Power Wheels car performs with the extra weight.
It should work more smoothly when you convert your car. If you find any defect in the car after a test drive, fix it. Once all is well you can now let your child drive the car and you can remotely control their car from scratch.
Final Thoughts
Many parents want to install a remote control in their car for the safety of their children. Because, when children drive at the highest speed, they can cause accidents. So parents want to do this to control the speed of their child’s car. Converting a power wheels car to remote control is a very simple task, you can do it by following the steps above. We hope you find this article on how to convert a Power Wheels car to remote control.
