Table of Contents
- Learn- How To Upgrade Battery In Power Wheels
- Can I Upgrade Battery in My Power Wheels?
- What’s the Point of Upgrading a Battery?
- Probable Safety Issue- Upgrading Battery in Power Wheels
- 12v to 18v Battery Upgrade
- Finishing Steps to Complete Battery Upgrade
- Final Thoughts
Learn- How To Upgrade Battery In Power Wheels
Tutorials on how to upgrade battery in power wheels can be bit confusing. The upgrade mainly depends on the existing specification of the battery you currently have. If you’ve got a 6v battery, you’ll obviously want to change it to 12v or more. However, no one wants to change battery voltage rating to the lower one.
It is possible to upgrade a 6-volt power wheel battery to a 12-volt battery. And, it’s also possible to convert a 12-volt battery to an 18-volt battery without hurting the motor’s performance. When replacing or upgrading the battery, make sure to include an inline fuse to prevent the engine from overheating as well.
You may boost the speed and performance of a power wheel toy car by upgrading the battery. The remainder of this page will discuss the details of replacing a power wheels battery in greater detail. It’ll include step-by-step directions. How To Upgrade 12v Power Wheels.
Can I Upgrade Battery in My Power Wheels?
Everyone can change a power wheels automobile battery with the correct equipment and a little research. Changing out a factory battery for a better one doesn’t require any specific electrical or engineering knowledge.
Upgrades to your power wheels’ batteries will void the manufacturer’s warranty, so be careful. Because of this, you’ll be responsible for any loss that occurs to the toy car after you improve it.
In most cases, power wheels come with a one-year warranty, as well as a six-month battery warranty. After the insurance has ended, it is common for the battery to need to be upgraded or replaced.
What’s the Point of Upgrading a Battery?
It’s not uncommon for parents to have conflicting ideas about whether or not it’s ok to upgrade a battery. Upgrading the battery has some disadvantages, but you can overcome those disadvantages by the advantages. Most significantly, you may avoid any and all dangers involving with a battery upgrade.
The cost of replacing a ride-on that your child has outgrown is less than the cost of upgrading the battery. The sluggishness of 6-volt and 12-volt motorized wheels is rapidly outgrown by children.
The ride-on car’s speed can be increased by up to 50 percent by upgrading the battery. Purchasing a new set of power wheels for your children for a fraction of the cost is a great way to save money.
Probable Safety Issue- Upgrading Battery in Power Wheels
An 18-volt battery will probably make the motors on the old type of power wheels burn out. To keep the motor safe, you can put in a 30 or 40 ATF fuse.
You must use metal cables and connectors if you wish to replace the batteries in your power wheels. The polarity of a short circuit or a fire is caused by misreading the polarity. Consequently, extreme caution is required throughout this stage of the upgrading.
Connections (Loose Ending)
Wire connections must be severed and reconnected during battery upgrade. The stress and vibrations from the spinning power wheel can knock your joints loose. So, proper fastening is necessary. To ensure that the mechanical bond is secure, crimping or soldering the joints is the best option.
12v to 18v Battery Upgrade
Super wheels come with a large 12-volt lead-acid battery that is difficult to charge. So, replacing them with a smaller battery makes sense if you want to reduce charging times and boost performance.
Here’s how to swap a 12-volt battery with an 18-volt power tool battery.
Modify the Interface
Before using an 18-volt Milwaukee drill battery with a super wheel, alter the connecting locations. You have two main options:
A dead 12-volt battery’s connection is possible for a retrieval. If the connector has proper wiring to the battery, trim both wires to the same length.
If the connector is inside the battery, pry it out. Gently insert a flathead screwdriver into the battery’s seam. Pry away the covering to reveal the connector’s wire. Lift the connector to reveal the wiring. Then, cut them one by one.
Remove the plastic covering on the ends to reveal the wire. Crimp a female blade terminal to the negative terminal. Crimp a butt connector on the positive battery terminal.
USB Battery Mod- Adapter
It converts the drill battery into a USB connector so you can charge your phone while working. Pry the adaptor open to reveal the battery connections. Turn it over and connect two wires to the back connection terminals. Drill two holes in the plastic covering for the cables.
Finishing Steps to Complete Battery Upgrade
Using Inline Fuse
Overload protection is critical while upgrading power wheels batteries to prevent fire. The motor can overheat and catch fire without an inline fuse. Use a 30-amp automotive fuse (ETF). A blown fuse protects your battery and vehicle from overheating. Then just replace the fuse and you’re done.
Fit the inline fuse. Cut the inline fuse holder wire in half (if it’s attached on both ends). Crimp the fuse side to the positive terminal of your connector.
Unplug it (if using the battery adapter). To use the super wheel, you must remove the USB battery connector. Cutting the plug voids the warranty. If utilizing an old battery’s connector, skip this step.
Use Motor Speed Control
An 18-volt battery doubles the speed and performance of a ride on. Installing a motor speed control helps your child adjust to the supercharged ride safely. The controller connects the motor and battery and controls the motor’s power.
So, we’ve show a detailed way to upgrade 12v battery to 18v in a power wheels. It’s quite easy if you’ve got the right tools and knowledge. Hence, there’s nothing to fret over upgrading a power wheels battery. It’s all about the game of patience. How To Soup Up A Power Wheels Car.
To avoid the motors from overheating and catching fire, you’ll need to install a 30 or 40 detachable Automotive Type Fuse (ATF). Both a lithium-ion power tool battery and an Sealed Lead Acid battery are good options. Lithium batteries are smaller, lighter, and take less time to charge. Where To Store Power Wheels.